Hey there! I’m a supplier of finishing mowers, and I’ve seen my fair share of issues with these machines. In this blog, I’ll share some tips on how to troubleshoot common problems with a finishing mower. Finishing Mower
1. Starting Problems
One of the most common issues you might face is difficulty starting the mower.
Dead Battery
A dead battery could be the culprit. Check the battery cables – make sure they’re clean and tightly connected. Over time, corrosion can build up on the terminals, preventing a good electrical connection. If the cables look corroded, you can clean them with a wire brush and some baking soda mixed with water.
If the battery is old (usually after 3 – 5 years), it might need to be replaced. You can test the battery using a voltmeter. A fully charged battery should read around 12.6 volts. If it’s significantly lower, it’s probably time for a new one.
Faulty Starter
Sometimes, the starter motor might be the problem. You’ll know this if you turn the key and all you hear is a clicking sound. Try tapping on the starter motor gently with a hammer. Sometimes, this can get a stuck solenoid working again. If that doesn’t work, you’ll likely need to replace the starter.
Bad Spark Plug
A fouled or worn – out spark plug can also prevent the mower from starting. Remove the spark plug and check its condition. If it’s dirty, you can clean it with a wire brush. But if the electrodes are worn down, it’s best to replace it. Make sure to use the correct type of spark plug for your mower.
2. Mower Blades Issues
Uneven Cutting
If your mower is leaving patches of uncut grass, it could be due to uneven blade height. First, park the mower on a flat surface. Then, use a blade height gauge to check the height of each blade at the outer edge. Adjust the height adjustment mechanism so that all blades are at the same height.
Another cause could be dull blades. Dull blades tear the grass instead of cutting it cleanly, leading to an uneven cut. You can sharpen the blades using a bench grinder or a file. Make sure to maintain the original angle of the blade while sharpening.
Worn – Out Blades
Over time, the blades can become worn and damaged. Look for cracks, chips, or excessive wear on the blades. If you notice any of these issues, it’s time to replace the blades. Using worn – out blades not only affects the quality of the cut but can also put extra stress on the mower’s engine.
3. Engine Performance Problems
Poor Power
If your mower seems to be lacking power, the air filter could be dirty. The air filter prevents dust and debris from entering the engine. When it gets clogged, the engine doesn’t get enough air, which can reduce its power. Remove the air filter and check its condition. If it’s dirty, you can clean it if it’s a foam filter. If it’s a paper filter, you’ll need to replace it.
The fuel system can also cause power issues. Check the fuel filter for any blockages. A clogged fuel filter restricts the flow of fuel to the engine, leading to poor performance. If the fuel filter is dirty, replace it.
Overheating
An overheating engine can be a serious problem. One common cause is a dirty cooling fin. The cooling fins on the engine block help dissipate heat. If they’re clogged with grass clippings and dirt, the engine can’t cool down properly. Use a brush or compressed air to clean the cooling fins.
Another possible cause is low coolant levels (if your mower has a liquid – cooled engine). Check the coolant reservoir and add coolant if necessary. Make sure to use the correct type of coolant for your mower.
4. Transmission Problems
Difficulty Shifting Gears
If you’re having trouble shifting gears on your mower, the clutch might be the issue. Check the clutch cable for proper adjustment. If it’s too loose or too tight, it can make shifting gears difficult. You can adjust the clutch cable according to the manufacturer’s instructions.
The transmission fluid level can also affect gear shifting. Low transmission fluid can cause the gears to slip or be hard to shift. Check the transmission fluid level and add fluid if needed. Make sure to use the recommended type of transmission fluid.
Noisy Transmission
A noisy transmission could be a sign of low fluid, worn bearings, or damaged gears. First, check the fluid level. If it’s low, add the appropriate fluid. If the noise persists, it might be a more serious problem. In this case, it’s best to have a professional take a look at the transmission.
5. Belt and Pulley Problems
Slipping Belt
A slipping belt can cause the blades to spin slowly or stop spinning altogether. Check the belt tension. If it’s too loose, it will slip. Most mowers have an adjustment mechanism to tighten the belt. Follow the manufacturer’s instructions to adjust the belt tension properly.
Also, check the belt for any signs of wear or damage. If the belt is cracked or frayed, it needs to be replaced.
Worn Pulleys
The pulleys that the belt runs on can also wear out over time. Look for signs of excessive wear, such as grooves or uneven surfaces on the pulleys. If the pulleys are worn, they can cause the belt to slip or wear out faster. Replace the worn pulleys to ensure proper belt operation.
Conclusion
Troubleshooting common problems with a finishing mower doesn’t have to be a headache. By following these tips, you can often identify and fix the issue on your own. Regular maintenance is also key to preventing many of these problems from occurring in the first place.
Land Preparation If you’re having more serious problems or if you’re not confident in your troubleshooting skills, don’t hesitate to reach out. We’re here to help as a finishing mower supplier. Whether you need replacement parts or advice on a particular issue, we can provide you with the support you need. If you’re in the market for a new finishing mower or need to restock on parts, feel free to contact us for procurement talks. We’ll be happy to discuss your needs and find the best solutions for you.
References
- Various mower user manuals
- Industry – standard maintenance guides
- Personal experience as a finishing mower supplier
Changzhou Kaideli Machinery Co., Ltd.
Changzhou Kaideli Machinery Co., Ltd. is one of the most professional finishing mower manufacturers and suppliers in China, providing high quality customized products with low price. We warmly welcome you to buy cheap finishing mower made in China here from our factory.
Address: 98#Xingchen Road, Hengshanqiao Town, Wujin District, Changzhou, Jiangsu, China
E-mail: export@czkaideli.com
WebSite: https://www.czkdl-agri.com/
